Jump to content


Photo

Cant connect 6 player game.


  • Please log in to reply
13 replies to this topic

#1 firatpwns

firatpwns

    Sergeant

  • Members
  • PipPipPip
  • 85 posts

Posted 14 November 2011 - 01:34 AM

Hi


I cant connect to other players when i try to play a game with 6 people.It seems only to work with 3 players.Any help would be appreciated.


Thank you.

#2 fir3w0rx

fir3w0rx

    Xwis Was Initially Striketeam

  • XWIS Buddies
  • PipPipPipPipPipPip
  • 2159 posts
  • Location:Out with your wife
  • XWIS Name: fir3w0rx

Posted 14 November 2011 - 03:14 AM

Which game? On the XWIS server, In YR you can have 6 players per game, but in RA2 the maximum is 4.

#3 firatpwns

firatpwns

    Sergeant

  • Members
  • PipPipPip
  • 85 posts

Posted 14 November 2011 - 03:41 AM

lol obviously its YR.And it is on xwis server of course.

I turned FW off and didn't make any difference.I just don't know where to begin with.I m using a new Internet now and I have a new pc ( bought it like 7 months ago ) but when i was using my old Internet it worked fine with the same pc as now.Since I have this new Internet I cant play with 6 people.I don't know if its the router or my pc...It could be my Virus scanner also.

Edited by firatpwns, 14 November 2011 - 03:50 AM.


#4 Olaf

Olaf

    Commander

  • XWIS Admin
  • PipPipPipPipPipPipPipPip
  • 13498 posts
  • XWIS Name: XTF

Posted 14 November 2011 - 10:10 AM

Your router is bad...

#5 firatpwns

firatpwns

    Sergeant

  • Members
  • PipPipPip
  • 85 posts

Posted 14 November 2011 - 01:20 PM

This is the one we are using right now.



Posted Image



The backside is as same as this one.

Posted Image



As you can see this is also wireless and i m using broadband because its better.Mine is in port 1.

Edited by firatpwns, 14 November 2011 - 01:22 PM.


#6 firatpwns

firatpwns

    Sergeant

  • Members
  • PipPipPip
  • 85 posts

Posted 14 November 2011 - 02:44 PM

So What do you suggest ? :)

#7 Olaf

Olaf

    Commander

  • XWIS Admin
  • PipPipPipPipPipPipPipPip
  • 13498 posts
  • XWIS Name: XTF

Posted 14 November 2011 - 05:35 PM

Try DMZ. Otherwise try a router with unrestricted NAT.

#8 firatpwns

firatpwns

    Sergeant

  • Members
  • PipPipPip
  • 85 posts

Posted 15 November 2011 - 03:35 AM

I m sorry I don't understand what you are saying :/ What do you mean by DMZ and unrestricted NAT ?

Ok I made a little research now and if I m correct,DMZ is a bridge between Lan and Internet ( unsafe Lan ) and NAT changes the intern ports in to extern ports.It translates the network address.But I don't know what these are for precisely.
Does this have something to do with the settings or do i have to buy it ? Can you explain me how to do it plz?

Thank you.

#9 firatpwns

firatpwns

    Sergeant

  • Members
  • PipPipPip
  • 85 posts

Posted 15 November 2011 - 11:57 PM

Could port forwarding YR work ? I don't know what to do help plz

#10 Olaf

Olaf

    Commander

  • XWIS Admin
  • PipPipPipPipPipPipPipPip
  • 13498 posts
  • XWIS Name: XTF

Posted 16 November 2011 - 12:13 AM

Port forwarding is unlikely to work. Try setting the DMZ.

#11 firatpwns

firatpwns

    Sergeant

  • Members
  • PipPipPip
  • 85 posts

Posted 16 November 2011 - 01:32 AM

Ok I ve found this.

http://support.netgear.com/app/answers/detail/a_id/1118


It says that i need to go to advanced than security.But there is no advanced.It says some routers use the WAN Setup options page instead.than It says Enter the servers IP address.
When I go to WAN there is no balk to type my IP in.

In the Start I see some informations...
Below that there is a link Disconnect
And Right below that there is DHCP Client Log and Security Log.
( Client Log : View information on LAN DHCP clients recorded on the router )
( Security Log : View any attempts that have been made to gain access to your network )
The Second menu button is Voice Settings...

The third one is DATA.
When I go there I see NAT and FIREWALL at the left side.

But it says :
Advanced Setup

''The router supports advanced functions like Stateful Packet Inspection, hacker attack detection, content filtering, access control, virtual servers and client filtering.

We recommend that you keep the default settings.''


When I click on NAT,It shows options that are Port Mapping,Special Application,Nat mapping table.

When I click on FIREWALL, it shows these options : Access Control,Mac Filter,URL Blocking,Schedule Rule.

Where do I type the Ip of the server ?


I don't know if this changes anything but I thought it might be good to mention it.I am using AVG Internet Security 2012.It has its own Firewall I guess...I've already tried to turn Firewall off from AVG.Repaired The First Decade and than Reinstalled again...The results are Same.

Edited by firatpwns, 16 November 2011 - 01:10 AM.


#12 firatpwns

firatpwns

    Sergeant

  • Members
  • PipPipPip
  • 85 posts

Posted 16 November 2011 - 04:29 PM

Is this the place where to do it ? If so than what do i type in the Trigger port,trigger type,public port and the public type ?
Remember mine is not the same as this one just the balk where u can type in.I only see NAT and FIREWALL there,the rest of the options is not shown.Instead of Advanced there is DATA. its like START-VOICE-DATA-EXTRAS.

Special Applications

Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications cannot work when Network Address Translation (NAT) is enabled. If you need to run applications that require multiple connections, specify the port normally associated with an application in the "Trigger Port" field, select the protocol type as TCP or UDP, then enter the public ports associated with the trigger port to open them for inbound traffic.
Note: The range of the Trigger Ports is from 1 to 65535.

Posted Image

#13 Olaf

Olaf

    Commander

  • XWIS Admin
  • PipPipPipPipPipPipPipPip
  • 13498 posts
  • XWIS Name: XTF

Posted 16 November 2011 - 04:42 PM

Nope. You might ask your modem supplier for help.

#14 firatpwns

firatpwns

    Sergeant

  • Members
  • PipPipPip
  • 85 posts

Posted 16 November 2011 - 04:55 PM

One of these ?

( NAT ) Port Mapping

You can configure the router as a virtual server so that remote users accessing services such as the Web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses. In other words, depending on the requested service (TCP/UDP port number), the router redirects the external service request to the appropriate server (located at another internal IP address). This tool can support both port ranges, multiple ports, and combinations of the two.

For example:

Port Ranges: ex. 100-150
Multiple Ports: ex. 25,110,80
Combination: ex. 25-100,80

There is a button below all of that ''Configure''.

( FIREWALL options ) Access Control

Access Control allows users to define the traffic type permitted or not-permitted to WAN port service. This page includes IP address filtering and MAC address filtering.
Enable Filtering Function ()
Normal Filtering Table (up to 10 computers):

Here is a ''configure'' button too.


MAC Filtering Table

This section helps provide MAC Filter configuration. When enabled, only MAC addresses configured will have access to your network. All other client devices will get denied access. This security feature can support up to 32 devices and applies to clients.

MAC Address Control ()
MAC Filtering Table (up to 32 computers):

Schedule Rule

This page defines schedule rule names and activates the schedule for use in the "Access Control" page.

Schedule Rule Table (up to 10 rules):


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users